Where Does the Remote Wire Go from the Amp

The remote wire from the amp is typically connected to a 12V power source, such as your vehicle’s fuse box. This connection provides an on/off signal for the amplifier when you turn it on and off. To ensure proper operation of the remote wire, make sure that each end of the wire is securely connected using appropriate connectors and electrical tape or shrink tubing.

The other end should be placed in a location where it will not be exposed to extreme temperatures, moisture or vibration. Additionally, never run any speaker wires through this same conduit as it can lead to interference with sound quality and performance.

The remote wire from the amplifier connects to the head unit, usually on a 12V+ terminal. This connection allows the head unit to turn on and off the amp automatically when playing music or powering down after a listening session. Make sure you connect this wire securely to avoid any potential electrical issues, as well as disconnecting it if you ever need to remove your amp.

Where Does the Remote Wire Go from the Amp

Credit: www.youtube.com

Where Do You Put the Remote Wire on an Amp?

When you’re setting up an amplifier in your car audio system, one of the most important steps is connecting the remote wire. This thin gauge wire serves as a turn-on signal from the head unit to amp and allows it to power up when the vehicle is running. The location of this connection will vary depending on your setup, but typically you’ll want to connect it either directly to the back of your radio or at a convenient point on your fuse box.

Before making any connections, make sure to check with both product manuals for specific instructions on where exactly each component should be connected. Once everything has been correctly wired up according to manufacturer recommendations, plug in the remote wire into its designated spot on your amp and secure it with a ring terminal or other connector that came with it. After that’s done, you can now move onto testing out all components of your sound system!

What Does the Remote Cable Do on the Amp?

The remote cable on an amplifier allows you to control the power and volume of your amp from another location. It is usually connected to a receiver, pre-amplifier or other outboard device that has the ability to send signals through the cable. This allows you to adjust the volume and power levels without having to be physically present at the amplifier itself.

The remote cable can also be used in conjunction with some sound systems allowing for automated sound system changes like changing between different equalization settings or switching between various input sources on a multi-channel setup. Additionally, it can allow users to control their amplifiers from their smartphones as well as providing additional features such as preset memory recall, multiple zone control, remote monitoring capabilities and more. Ultimately, this gives musicians and audio engineers greater flexibility when setting up their rigs by enabling them to make adjustments quickly and easily without having to physically reach over and turn knobs on an amp’s faceplate which could lead to potential damage if done carelessly or too forcefully.

Can You Hook Amp Remote Wire to Battery?

Yes, you can hook an amp remote wire to a battery. This is typically done when the car stereo does not have a dedicated power source for the amplifier, and needs to be powered from the same battery that powers the vehicle’s electrical system. To do this, you must run two sets of cables from the amp to your vehicle’s main positive terminal on its battery – one set of cables will feed power directly into your amp and another set of cables will act as a ground connection back to your vehicles’ negative terminal.

When connecting these wires make sure they are securely connected with no exposed wiring or loose connections which could cause issues such as short circuits or fires in extreme cases. Additionally, ensure that both strands of wire are properly insulated so as not to create any sparks or shorts while running them through metal components inside your car engine bay. Once everything is secure and connected correctly you should find that powering up your amplifier is now possible via direct connection from your vehicle’s battery!

Can I Use My Amp Without Remote Wire?

Yes, you can use your amp without a remote wire. However, this will mean that the amp won’t be able to turn on and off with the rest of your car audio system. Without the remote wire connected, the amp will stay “on” at all times when there is power supplied to it.

This could cause unnecessary drain on your vehicle’s battery and possibly even damage to some components if not monitored closely. To avoid these complications and make sure your amplifier works correctly in tandem with other audio components in your vehicle, it is recommended that you connect a remote wire for optimal performance.

car stereo wiring remote turn on and power antenna

How to Turn on Amp Without Remote Wire

If you are looking to turn on your car amplifier without a remote wire, there is an easy solution. All you need to do is connect the positive lead from the battery directly to the amp’s power terminal. This will provide continuous power and will ensure that your amp turns on automatically when your car starts.

Make sure that all other electrical components in your system are wired properly before connecting them directly to the battery for safety reasons.

What Wire Does the Remote Wire Connect to

The remote wire connects to the power antenna or amplifier “turn-on” lead in a car audio system. This lead allows the amplifier to turn on when the radio is powered up, and also allow for an automated power down feature when the radio is turned off. The remote wire should be connected directly to the positive (+) terminal of this lead.

Car Amp Remote Wire Bypass

When installing a car amplifier, it’s important to connect the remote wire in order for your amp to turn on and off. However, if you are unable to locate or access the remote wire from your vehicle’s wiring harness, an alternative method of connecting a remote wire is by bypassing it directly at the amplifier itself. Bypassing the remote wire can be done by finding an open terminal (or creating one) and attaching a 12V power source with enough current capacity to support the amp.

This will ensure that your amplifier turns on when you want it to without having to track down and access any existing wiring.

Remote Wire for Amp to Fuse Box

Using a remote wire for an amp to fuse box is the most efficient way of connecting your amplifier to the power supply. It allows you to bypass the factory wiring, making it easier and faster to install. By connecting directly from the battery in your vehicle to the amp, there are no worries about overloading existing car audio circuits.

The remote wire also prevents any interference that may be caused by other electrical components on board, ensuring optimal sound performance.

Remote Turn on Wire on Radio

The remote turn on wire is an important feature found in modern car radio systems. This wire allows the power to be turned on and off remotely, usually from a switch located elsewhere in the vehicle. By using this feature, it’s possible to control the radio without having to reach inside and press the power button.

Additionally, when properly installed, this can be used as an anti-theft measure by allowing you to activate or deactivate your stereo system at will.

How Does a Remote Turn on Wire Work

A remote turn on wire is a type of wiring system used to provide power to an amplifier or other audio device when the vehicle’s ignition switch is activated. This feature allows the user to control their stereo system with ease, as they do not have to manually plug in and unplug wires each time they start or stop their vehicle. The remote turn on wire works by sensing when there is an electrical connection between the battery and ignition, which then sends a signal that triggers the power supply for your amplifier.

Remote Wire for Amp Gauge

Remote Wire for Amp Gauge is a must-have accessory when it comes to installing an aftermarket amplifier or subwoofer in your vehicle. This wire provides power to the amp gauge, which reads the current draw of your audio components and informs you if they are drawing too much power and will cause any type of damage. It also helps in optimizing the performance of your car’s electrical system by providing a safe and proper connection between your amplifier and battery.


Overall, this blog post has provided a comprehensive overview of the importance and function of the remote wire in car audio systems. It is important to remember that when wiring an amp, you must ensure the remote wire is securely connected to the power antenna or accessory socket. Additionally, it is important to know what type of amplifier you have and if it requires a specific type of cable for its connection.

By following these simple steps, you can easily install your amp correctly and enjoy your music on the road safely.