How to Reset Park Assist on Silverado

If you’re the owner of a Chevrolet Silverado, you may at some point need to reset your park assist system. Park assist is a great feature that helps you park your truck in tight spots by giving you an audio alert when you get too close to an object. If your park assist system starts acting up, it’s likely because it needs to be reset.
Luckily, this is a pretty easy process that only takes a few minutes.

  • Park your vehicle in a safe and level location
  • Locate the park assist button on your Silverado’s dash
  • This button is typically labeled with “PARK ASSIST” or a similar phrase
  • Press and hold the park assist button for several seconds until you hear a beep from the system, indicating that it has been reset
  • Drive your vehicle as usual, and the park assist system will now be fully functional again

Park Assist Won’T Turn on

If your park assist won’t turn on, there are a few things you can check.

First, make sure that your car is in park and the parking brake is engaged.

Next, check to see if there are any objects blocking the sensors on the front or rear of your car.

Finally, if your car has an automatic transmission, make sure that it is in Park mode. If none of these things solve the problem, then you may need to take your car to a mechanic to have it checked out.

How to Reset Park Assist on Silverado


How Do I Reset My Park Assist Sensor?

  • If your park assist sensor is not functioning properly, there are a few things you can do to reset it. First, check the owner’s manual for your specific vehicle to see if there are any instructions on how to reset the park assist sensor. If there are no instructions in the manual, you can try the following:
  • Park your car in an open area where there are no obstacles around it.
  • Turn off the engine and set the parking brake.
  • Get out of the car and close all of the doors.
  • Wait for five minutes and then get back in the car and turn on the engine.
  • Put the car in reverse and slowly back up until you hear a beeping sound from the park assist sensor (this may take a few tries).
  • Once you hear the beeping sound, put the car in drive and continue driving forward until you hear another beep from the sensor (this may also take a few tries).

Why Does My 2013 Chevy Silverado Say Park Assist Blocked?

If your 2013 Chevy Silverado is saying “Park Assist Blocked,” it means that the vehicle’s Park Assist feature has been disabled. This could be for a number of reasons, including: -The Park Assist feature may have been turned off in the vehicle’s settings.

To check if this is the case, go to your vehicle’s infotainment system and navigate to the settings menu. From there, look for the Park Assist setting and make sure it is turned on. -There could be an issue with one of the sensors that enable Park Assist.

If this is the case, you’ll need to take your vehicle to a Chevrolet dealership or service center so they can diagnose and fix the problem. -It’s also possible that there is something blocking the sensor, such as dirt or debris. Again, you’ll need to take your car to a Chevrolet dealership or service center so they can inspect and clean the sensor if necessary.

What Causes Park Assist to Stop Working?

If your park assist system is no longer working, there are a few potential causes. The most common cause is simply that the sensors need to be cleaned. Over time, dirt and debris can build up on the sensors, causing them to become less effective.

You can clean the sensors yourself with a cloth or you can take your car to a professional who will have the proper equipment to clean them more thoroughly. Another potential cause of a non-working park assist system is a problem with the wiring. If there is any damage to the wires, it could prevent the signal from reaching the sensor properly.

In this case, you’ll likely need to take your car to a mechanic in order to have the damage repaired. Finally, if none of these solutions work, it’s possible that there is a problem with one of the components in the park assist system itself. In this case, you’ll again need to take your car to a professional for diagnosis and repair.

Why Does My Truck Say Park Assist Off?

There are a number of reasons why your truck’s park assist system may be turned off. The most common reason is that the system has been manually turned off by the driver. Other potential reasons include a malfunction in the park assist system, or a low battery.

If you’re not sure why your park assist is turned off, it’s best to consult your truck’s owner’s manual or contact a qualified mechanic.

Troubleshooting Chevrolet Service Park Assist


In conclusion, resetting the Park Assist system on a Silverado can be a straightforward process if the steps are followed correctly. By referring to the vehicle’s owner’s manual or seeking guidance from the manufacturer’s official resources, one can locate the specific instructions for resetting the Park Assist system on their Silverado model.

It is essential to ensure that all the necessary conditions are met, such as being parked on a level surface and having no obstructions around the vehicle. By carefully following the recommended steps, drivers can effectively reset the Park Assist system and restore its functionality.

However, if the issue persists or the reset process seems challenging, it is advisable to consult a certified technician or reach out to a Chevrolet dealership for further assistance. Remember, prioritizing safety and proper vehicle maintenance is crucial when dealing with any vehicle system, including the Park Assist feature.