If you’re receiving a “Perform Service” message on your Dodge Ram, it typically indicates that there is an issue that requires attention or regular maintenance. To remove this message, you’ll need to identify the underlying problem and take the necessary steps to resolve it.
Here are some general steps you can follow:
1. Check the owner’s manual:
Consult your Dodge Ram’s owner’s manual for information on the “Perform Service” message. It may provide specific instructions on what the message means and how to address it.
2. Perform basic checks:
Before taking any further action, perform some basic checks on your vehicle. This includes inspecting the engine oil level, coolant level, transmission fluid level, and brake fluid level. Ensure they are all at the recommended levels.
3. Check for error codes:
Use an OBD-II scanner or take your truck to a mechanic who can connect a diagnostic scanner to identify any error codes. These codes can provide valuable information about the specific issue causing the “Perform Service” message.
4. Address the specific issue:
Once you have identified the problem through error codes or a thorough inspection, take the necessary steps to address it. This may involve replacing a faulty part, performing routine maintenance, or addressing any other issue that has been identified.
5. Reset the message:
After resolving the underlying issue, you may need to reset the “Perform Service” message. There are a few different methods to reset this message, depending on the model year and specific features of your Dodge Ram. Here are a couple of common methods:
- Disconnect the battery:
Disconnect the negative terminal of the battery and leave it disconnected for about 15 minutes. Then reconnect the terminal and start the vehicle. This should reset the message. However, keep in mind that disconnecting the battery will also reset any other settings and systems in your truck.
- Use a scan tool:
If disconnecting the battery doesn’t work or if you want to avoid resetting other settings, you can use an OBD-II scan tool that has the capability to reset service messages. Follow the instructions provided with the scan tool to reset the message.
6. Verify the message is cleared:
After performing the reset procedure, start your Dodge Ram and check if the “Perform Service” message is no longer displayed.
Perform Service Ram 2500 Reset
The Ram 2500 is a light duty truck that was introduced in 1994. It is available in both two-wheel and four-wheel drive configurations. The Ram 2500 is powered by a V8 engine and has a maximum payload capacity of 1,500 pounds.
The Ram 2500 comes with several different factory reset options:
Option One:
1. Turn the ignition switch to the ON/RUN position without starting the engine
2. Fully depress and release the accelerator pedal three times within five seconds
3. Turn the ignition switch to the LOCK/OFF position
4. Start the engine to verify that the indicator has been reset
5. If the indicator does not reset, repeat steps 1 through 5
Option Two:
1. With your foot on the brake, press and hold the TRIP/ODOM button for about five seconds until RESET appears in the odometer display window

Credit: www.igotacummins.com
How Do I Get Rid of Perform Service Massage on My Ram?
If you’re looking to get rid of the “perform service” message on your RAM, there are a few things you can try.
First, make sure that all of your RAM modules are properly seated and secured in their slots. If they seem loose, try removing and reinstalling them.
Sometimes this can fix the issue. If that doesn’t work, you can try resetting your BIOS settings to their defaults. This will usually clear up any minor issues that may be causing the message to appear.
Finally, if all else fails, you may need to replace your RAM modules altogether.
If you have warranty coverage, now would be a good time to use it. Otherwise, be prepared to shell out some cash for new RAM.
How Do I Delete Perform Service on 6.7 Cummins?
If you’re looking to delete your 6.7 Cummins, there are a few things you need to do first.
First, you’ll need to find a reputable service shop that can perform the deletion. Once you’ve found a shop, they will need to disable the emission controls on your truck. This process is typically done by reprogramming the truck’s computer.
After the emission controls have been disabled, the service shop will then install an aftermarket exhaust system. This new exhaust system will not have any emissions controls, which means your truck will no longer be street legal.
However, it will allow your engine to breathe better and run more efficiently.
What Does Perform Service Mean on Dodge Ram?
When you take your Dodge Ram in for service, the technicians will perform a variety of tasks to keep your truck running smoothly. They will check the engine oil and filter, top off fluids, inspect the brakes and tires, and clean or replace the air filter. In addition, they may also rotate the tires, change the spark plugs, or flush the cooling system.
By performing these routine maintenance tasks, you can help extend the life of your truck and avoid costly repairs down the road.
Reset the Perform Service Message on a Ram 6.7L Cummins